11gR1 IO-Fencing 的hangcheck-timer 模块说明

一.官网的说明

参考MOS：Linux: Hangcheck-Timer Module Requirements for Oracle 9i, 10g, and11gR1 RAC [ID 726833.1]Hangcheck_timermodule is required to run a supported configuration in Oracle Real ApplicationClusters environments on Linux, with Oracle releases 9i, 10g, or 11gR1RAC. This note identifies and outlines the requirements needed toconfigure hangcheck-timer in an Oracle Enterprise Linux, Red Hat Linux, or SUSELinux environment.在Linux 环境下Oracle 9i，10g，11gR1 的RAC 需要配置Hangcheck_timer模块。Note : Hangheck timer is notrequired starting with Oracle Clusterware 11gR2注意，在模块在11gR2的RAC 中已经不在需要配置了。Starting in release 9.2.0.2and later, Oracle RAC environments required using a new I/O fencing model,named the hangcheck-timer module. This module was implemented to replace theWatchdog module, which provided similar fencing functionality. Hangcheck-timerwas subsequently delivered as part of the standard kernel distribution forLinux kernel releases 2.4 and above. 从9.2.0.2版本开始，ORACLERAC环境需要使用一个新的I/O fencing模块，叫做hangcheck-timer模块。这个模块用来代替Watchdog模块，提供类似的fencing功能。Hangcheck-timer模块是标准的linux2.4以上的内核中的一个子功能被发布。Hangcheck-timer shouldbe loaded at boot time, and monitors the Linux kernel for long operatingsystem hangs that could affect the reliability of a RAC node. It runs inkernel mode and uses the Time Stamp Counter （TSC） to catch scheduling delays ornode hangs. This is done by setting a timer, then checking when the timerfires as to whether it was delayed by more than the allowed margin oferror. If the duration exceeds the allowed time of （hangcheck_tick +hangcheck_margin seconds）, the machine is restarted. Hangcheck-timer willnot cause reboots to occur due to CPU starvation.--Hangcheck-timer应该在系统启动的时候被加载, 并对于能够影响RAC节点稳定性的长时间的系统操作HANG进行内核监控。它运行在内核级别并使用Time Stamp Counter（TSC）来捕捉调度的延迟和节点HANG。这是通过设置一个timer，然后检查这个timer的fires情况来判断是否延迟是否超过了误差的幅度。如果这个周期超过了允许的时间（也就是hangcheck_tick+hangcheck_margin秒），机器将会被重启，如果是CPU资源不足的时候，Hangcheck-timer将不会导致重启。Hangcheck-timer requiresthree configuration parameters:--Hangcheck-timer有三个配置参数:（1） hangcheck_tick - defines howoften, in seconds, the hangcheck-timer checks the node for hangs. The defaultvalue is 60 seconds.-- hangcheck_tick：定义了hangcheck-timer检查节点是否hang的频率，单位是秒，缺省是60秒.（2） hangcheck_margin - defines howmuch margin is allowed, in seconds, between expected scheduling and realscheduling time. The default value is 180 seconds.--hangcheck_margin：定义期望的和真正的scheduling之间允许的误差，单位是秒，缺省值是180秒.（3） hangcheck_reboot - determinesif the hangcheck-timer restarts the node if the kernel fails to respond withinthe sum of the hangcheck_tick and hangcheck_margin parameter values. If thevalue of hangcheck_reboot is equal to or greater than 1, then thehangcheck-timer module restarts the system. If the hangcheck_reboot parameteris set to zero, then the hangcheck-timer module will not reboot the node,even if a hang is detected. The default value varies by kernelversion. In the 2.4 kernel, the default is 1. In 2.6 kernels, thedefault is 0.--hangcheck_reboot：定义了如果内核在hangcheck-tick和hangcheck-margin相加的时间内响应失败的话，hangcheck-timer是否重启节点。如果hangcheck_reboot的值大于等于1,hangcheck-timer模块将会重启系统；如果设置为0，则即使系统hang的时候hangcheck-timer也不会重启系统。在linux 2.4的内核中，这个缺省值是1；在2.6的内核中，缺省值是0。当hangcheck_reboot=1并且满足下面的公式时，hangcheck-timer将reboot系统: system hang time > （hangcheck_tick + hangcheck_margin）All hangcheck-timer defaultvalues should be explicitly overridden when loading the kernel module, based onthe Oracle release as follows: --所有的hangcheck-timer的参数的缺省值必须在加载内核模块的时候被显式的覆盖，不同的oracle版本可以按照下面来设置：（1）9i: Assuming thedefault setting of "oracm misscount" is set to 220 seconds: hangcheck_tick=30hangcheck_margin=180 hangcheck_reboot=1--9i: 假如"oracle misscount"的缺省设置是220秒，则hangcheck_tick=30hangcheck_margin=180 hangcheck_reboot=1

（2）10g/11gR1: Assuming thedefault setting of "CSS misscount" is set to either 30 or 60seconds:hangcheck_tick=1hangcheck_margin=10 hangcheck_reboot=1--10g/11gR1: 假如"CSS misscount"的设置是30或者60秒，则hangcheck_tick=1hangcheck_margin=10 hangcheck_reboot=1 You must always ensure thatthe Cluster misscount setting is greater than the sum of the setting forhangcheck_tick + hangcheck_margin.--注意：你必须设置集群的misscount值大于hangcheck_tick + hangcheck_margin之和。When running OracleClusterware on Linux, hangcheck-timer should always be configured on each RACcluster node, as the functionality of this module is required to provide I/O Fencingto ensure no stray writes will occur from an evicted node in a RACcluster. To verify if the hangcheck-timer module is running on a nodeexecute as the root or oracle user: --Linux 平台上的Clusterware，需要在每个节点上配置hangcheck-timer模块，可以用root用户执行如下命令来验证hangcheck-timer是否运行：# /sbin/lsmod | grep hangcheckhangcheck-timer 2672 0If the hangcheck-timer moduleis loaded （running） you will see output similar to above. When hangcheck-timeris not loaded no output is generated, and the command prompt is returned to theuser.In an Oracle Enterprise Linux,Red Hat 4/5, or SUSE 9/10 environment the hangcheck-timer module is loadedusing the modprobe command:--使用如下命令来装载hangcheck-timer：# modprobe hangcheck-timer hangcheck_tick=1 hangcheck_margin=10hangcheck_reboot=1In order to ensure the moduleis loaded at boot time, you should also place the same command in the appropriatelocal command execution directory （e.g. /etc/rc.d/rc.local, or/etc/init.d/boot.local）. In earlier releases, hangcheck-timer was loadedusing insmod in place of modprobe. Consult your release specific documentationto determine which initialization method is required. --为了确保在系统启动时就装载了hangcheck-timer模块，我们可以将命令添加到/etc/rc.d/rc.local,or /etc/init.d/boot.local中。Hangcheck-timer will providemessage logging to the system messages log when a failure is detected, and anode restart is initiated by the module:--当hangcheck-timer检测到系统hang时，会在系统log里记录日志并重启系统。（1） When Hangcheck-timer reboots itmay leave "Hangcheck: hangcheck is restarting the machine" message in/var/log/messages。-- hangcheck-timer的启动信息都会记录在系统日志里“ /var/log/messages”，重启时会记录"Hangcheck:hangcheck is restarting the machine"信息到/var/log/messages（2） If you see the followingmessage in /var/log/messages: "Hangcheck: hangcheck value pastmargin！" this means a reboot was required but was not performed, becausehangcheck_reboot was not set to 1. If this message is seen, you mustreload the hangcheck module as described earlier in this note, with thehangcheck_reboot value set to 1.--如果你看到/var/log/messages中有"Hangcheck:hangcheck value past margin！"消息，表示系统需要重启但是没有重启，因为hangcheck-reboot参数没有设置为1。注：Bug:6125546 which can preventhangcheck-timer from rebooting in RHEL4 （fixed in 2.6.9.56 or RHEL4.6）

Oracle工具之autotrace的开启与选项说明Oracle cp: cannot stat `/DISCARD/": No such file or directory 说明相关资讯 ORACLE 10G

Oracle 10g（10.2.0.4）升级到10.2.0 （04月10日）
Oracle 10g 一主多备的搭建技巧（07/31/2015 15:31:51）
多平台下的32位和64位Oracle 10g下（02/18/2015 10:38:21）

Oracle 10g实现只读表的N种方法（08/05/2015 10:54:35）
Oracle 10g中约束与列属性NULLABLE （03/07/2015 19:22:46）
Oracle 10g Clusterware Votedisk （01/16/2015 14:09:54）

本文评论查看全部评论（0）